Anet a8 plus con skr mini e3 v3.0 endstop non funzionano

BND420 · 1 Novembre 2022

Salve a tutti, ho installato di recente sulla mia anet a8 plus una btt skr mini e3 v3.0 e attualmente sto controllando che tutto funzioni procendo a step, motori ok endstop non funzionanti, nessuno dei 3, il firmaware e' il 2.0.9.5, architettura é impostata su stm32g0 e l'enviroment é stm32g0b1re_btt questi sono i settings di configuration.h e sotto di configuration_adv.h, spero di aver riportato tutto, dove ho sbagliato? i cablaggi sono stati controllati piú volte e sembrano anche loro corretti

#define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate

//===========================================================================

//============================== Endstop Settings ===========================

//===========================================================================

// @section homing

// Specify here all the endstop connectors that are connected to any endstop or probe.

// Almost all printers will be using one per axis. Probes will use one or more of the

// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.

#define USE_XMIN_PLUG

#define USE_YMIN_PLUG

#define USE_ZMIN_PLUG

//#define USE_IMIN_PLUG

//#define USE_JMIN_PLUG

//#define USE_KMIN_PLUG

//#define USE_XMAX_PLUG

//#define USE_YMAX_PLUG

//#define USE_ZMAX_PLUG

//#define USE_IMAX_PLUG

//#define USE_JMAX_PLUG

//#define USE_KMAX_PLUG

// Enable pullup for all endstops to prevent a floating state

//#define ENDSTOPPULLUPS

#if DISABLED(ENDSTOPPULLUPS)

// Disable ENDSTOPPULLUPS to set pullups individually

//#define ENDSTOPPULLUP_XMIN

//#define ENDSTOPPULLUP_YMIN

//#define ENDSTOPPULLUP_ZMIN

//#define ENDSTOPPULLUP_IMIN

//#define ENDSTOPPULLUP_JMIN

//#define ENDSTOPPULLUP_KMIN

//#define ENDSTOPPULLUP_XMAX

//#define ENDSTOPPULLUP_YMAX

//#define ENDSTOPPULLUP_ZMAX

//#define ENDSTOPPULLUP_IMAX

//#define ENDSTOPPULLUP_JMAX

//#define ENDSTOPPULLUP_KMAX

//#define ENDSTOPPULLUP_ZMIN_PROBE

#define ENDSTOPPULLUP_ZMIN_PROBE

#endif

// Enable pulldown for all endstops to prevent a floating state

//#define ENDSTOPPULLDOWNS

#if DISABLED(ENDSTOPPULLDOWNS)

// Disable ENDSTOPPULLDOWNS to set pulldowns individually

//#define ENDSTOPPULLDOWN_XMIN

//#define ENDSTOPPULLDOWN_YMIN

//#define ENDSTOPPULLDOWN_ZMIN

//#define ENDSTOPPULLDOWN_IMIN

//#define ENDSTOPPULLDOWN_JMIN

//#define ENDSTOPPULLDOWN_KMIN

//#define ENDSTOPPULLDOWN_XMAX

//#define ENDSTOPPULLDOWN_YMAX

//#define ENDSTOPPULLDOWN_ZMAX

//#define ENDSTOPPULLDOWN_IMAX

//#define ENDSTOPPULLDOWN_JMAX

//#define ENDSTOPPULLDOWN_KMAX

//#define ENDSTOPPULLDOWN_ZMIN_PROBE

#endif

// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).

#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.

#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define I_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define J_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define K_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.

#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.

// Enable this feature if all enabled endstop pins are interrupt-capable.

// This will remove the need to poll the interrupt pins, saving many CPU cycles.

#define ENDSTOP_INTERRUPTS_FEATURE

/**

* Endstop Noise Threshold

*

* Enable if your probe or endstops falsely trigger due to noise.

*

* - Higher values may affect repeatability or accuracy of some bed probes.

* - To fix noise install a 100nF ceramic capacitor in parallel with the switch.

* - This feature is not required for common micro-switches mounted on PCBs

* based on the Makerbot design, which already have the 100nF capacitor.

*

* :[2,3,4,5,6,7]

*/

//#define ENDSTOP_NOISE_THRESHOLD 2

// Check for stuck or disconnected endstops during homing moves.

//#define DETECT_BROKEN_ENDSTOP

//===========================================================================

//============================= Z Probe Options =============================

//===========================================================================

// @section probes

//

// See https://marlinfw.org/docs/configuration/probes.html

//

/**

* Enable this option for a probe connected to the Z-MIN pin.

* The probe replaces the Z-MIN endstop and is used for Z homing.

* (Automatically enables USE_PROBE_FOR_Z_HOMING.)

*/

#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN

// Force the use of the probe for Z-axis homing

//#define USE_PROBE_FOR_Z_HOMING

/**

* Z_MIN_PROBE_PIN

*

* Define this pin if the probe is not connected to Z_MIN_PIN.

* If not defined the default pin for the selected MOTHERBOARD

* will be used. Most of the time the default is what you want.

*

* - The simplest option is to use a free endstop connector.

* - Use 5V for powered (usually inductive) sensors.

*

* - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:

* - For simple switches connect...

* - normally-closed switches to GND and D32.

* - normally-open switches to 5V and D32.

*/

//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default

/**

* Z Servo Probe, such as an endstop switch on a rotating arm.

*/

//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector.

//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles

// Direction of endstops when homing; 1=MAX, -1=MIN

// :[-1,1]

#define X_HOME_DIR -1

#define Y_HOME_DIR -1

#define Z_HOME_DIR -1

//#define I_HOME_DIR -1

//#define J_HOME_DIR -1

//#define K_HOME_DIR -1

// @section machine

// The size of the printable area

#define X_BED_SIZE 300

#define Y_BED_SIZE 300

// Travel limits (mm) after homing, corresponding to endstop positions.

#define X_MIN_POS -26

#define Y_MIN_POS -6

#define Z_MIN_POS 0

#define X_MAX_POS 300

#define Y_MAX_POS 297

#define Z_MAX_POS 350

//#define I_MIN_POS 0

//#define I_MAX_POS 50

//#define J_MIN_POS 0

//#define J_MAX_POS 50

//#define K_MIN_POS 0

//#define K_MAX_POS 50

/**

* Software Endstops

*

* - Prevent moves outside the set machine bounds.

* - Individual axes can be disabled, if desired.

* - X and Y only apply to Cartesian robots.

* - Use 'M211' to set software endstops on/off or report current state

*/

// Min software endstops constrain movement within minimum coordinate bounds

#define MIN_SOFTWARE_ENDSTOPS

#if ENABLED(MIN_SOFTWARE_ENDSTOPS)

#define MIN_SOFTWARE_ENDSTOP_X

#define MIN_SOFTWARE_ENDSTOP_Y

//#define MIN_SOFTWARE_ENDSTOP_Z

#define MIN_SOFTWARE_ENDSTOP_I

#define MIN_SOFTWARE_ENDSTOP_J

#define MIN_SOFTWARE_ENDSTOP_K

#endif

// Max software endstops constrain movement within maximum coordinate bounds

#define MAX_SOFTWARE_ENDSTOPS

#if ENABLED(MAX_SOFTWARE_ENDSTOPS)

#define MAX_SOFTWARE_ENDSTOP_X

#define MAX_SOFTWARE_ENDSTOP_Y

#define MAX_SOFTWARE_ENDSTOP_Z

#define MAX_SOFTWARE_ENDSTOP_I

#define MAX_SOFTWARE_ENDSTOP_J

#define MAX_SOFTWARE_ENDSTOP_K

#endif

#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)

//#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD

#endif

/**

* Filament Runout Sensors

* Mechanical or opto endstops are used to check for the presence of filament.

// Validate that endstops are triggered on homing moves

#define VALIDATE_HOMING_ENDSTOPS

configuration_adv.h:

// If you want endstops to stay on (by default) even when not homing

// enable this option. Override at any time with M120, M121.

//#define ENDSTOPS_ALWAYS_ON_DEFAULT

//#define DUAL_X_CARRIAGE

#if HAS_X2_STEPPER && DISABLED(DUAL_X_CARRIAGE)

//#define INVERT_X2_VS_X_DIR // X2 direction signal is the opposite of X

//#define X_DUAL_ENDSTOPS // X2 has its own endstop

#if ENABLED(X_DUAL_ENDSTOPS)

#define X2_USE_ENDSTOP _XMAX_ // X2 endstop board plug. Don't forget to enable USE_*_PLUG.

#define X2_ENDSTOP_ADJUSTMENT 0 // X2 offset relative to X endstop

#endif

#if HAS_DUAL_Y_STEPPERS

//#define INVERT_Y2_VS_Y_DIR // Y2 direction signal is the opposite of Y

//#define Y_DUAL_ENDSTOPS // Y2 has its own endstop

#if ENABLED(Y_DUAL_ENDSTOPS)

#define Y2_USE_ENDSTOP _YMAX_ // Y2 endstop board plug. Don't forget to enable USE_*_PLUG.

#define Y2_ENDSTOP_ADJUSTMENT 0 // Y2 offset relative to Y endstop

#endif

//

// Multi-Z steppers

//

#ifdef Z2_DRIVER_TYPE

//#define INVERT_Z2_VS_Z_DIR // Z2 direction signal is the opposite of Z

//#define Z_MULTI_ENDSTOPS // Other Z axes have their own endstops

#if ENABLED(Z_MULTI_ENDSTOPS)

#define Z2_USE_ENDSTOP _XMAX_ // Z2 endstop board plug. Don't forget to enable USE_*_PLUG.

#define Z2_ENDSTOP_ADJUSTMENT 0 // Z2 offset relative to Y endstop

#endif

#ifdef Z3_DRIVER_TYPE

//#define INVERT_Z3_VS_Z_DIR // Z3 direction signal is the opposite of Z

#if ENABLED(Z_MULTI_ENDSTOPS)

#define Z3_USE_ENDSTOP _YMAX_ // Z3 endstop board plug. Don't forget to enable USE_*_PLUG.

#define Z3_ENDSTOP_ADJUSTMENT 0 // Z3 offset relative to Y endstop

#endif

#ifdef Z4_DRIVER_TYPE

//#define INVERT_Z4_VS_Z_DIR // Z4 direction signal is the opposite of Z

#if ENABLED(Z_MULTI_ENDSTOPS)

#define Z4_USE_ENDSTOP _ZMAX_ // Z4 endstop board plug. Don't forget to enable USE_*_PLUG.

#define Z4_ENDSTOP_ADJUSTMENT 0 // Z4 offset relative to Y endstop

#endif

//#define SENSORLESS_BACKOFF_MM { 2, 2, 0 } // (mm) Backoff from endstops before sensorless homing

#define HOMING_BUMP_MM { 5, 5, 2 } // (mm) Backoff from endstops after first bump

#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)

//#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (mm) Backoff from endstops after homing

//#define QUICK_HOME // If G28 contains XY do a diagonal move first

//#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X

//#define HOME_Z_FIRST // Home Z first. Requires a Z-MIN endstop (not a probe).

//#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first

/**

* Abort SD printing when any endstop is triggered.

* This feature is enabled with 'M540 S1' or from the LCD menu.

* Endstops must be activated for this option to work.

*/

//#define SD_ABORT_ON_ENDSTOP_HIT

// M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe

dziobu · 1 Novembre 2022

Prova a sblocare:

#define ENDSTOPPULLUPS

Killrob · 1 Novembre 2022

e poi prova a collegare la stampante al pc e con repetier host controllare che succede quando dai un M119

BND420 · 4 Novembre 2022

scusate la risposta tardiva, mi da

x min open

y min TRIGGERED

z min TRIGGERED

(risolto)

Modificato 5 Novembre 2022 da BND420

Fabrizio73 · 8 Dicembre 2022

Il 4/11/2022 at 14:56, BND420 ha scritto:

scusate la risposta tardiva, mi da

x min open

y min TRIGGERED

z min TRIGGERED

(risolto)

Ciao

come hai fatto a caricare il marlin sulla skr mini e3? Cosa hai usato ? Arduino o visual? Io non riesco a caricare marlin mi da una mano?

FoNzY · 8 Dicembre 2022

12 minuti fa, Fabrizio73 ha scritto:

Ciao

come hai fatto a caricare il marlin sulla skr mini e3? Cosa hai usato ? Arduino o visual? Io non riesco a caricare marlin mi da una mano?

è una conversazione vecchia di un mese...se hai problemi apri un post apposito...anche perche' "come hai fatto a caricare" non è che abbia tutto sto gran senso come domanda....ci saranno milioni di tutorial sul tubo....